This is the documentation for Cloudera Manager 5.1.x.
Documentation for other versions is available at Cloudera Documentation.

External PostgreSQL Database

Installing the External PostgreSQL Server

  • If you already have a PostgreSQL database set up, you can skip to the section Configuring and Starting the PostgreSQL Server to verify that your PostgreSQL configurations meet the requirements for Cloudera Manager.
  • It is important that the data directory, which by default is /var/lib/postgresql/data/, is on a partition that has sufficient free space.
  1. Use one or more of the following commands to set the locale:
    export LANGUAGE=en_US.UTF-8
    export LANG=en_US.UTF-8
    export LC_ALL=en_US.UTF-8
    locale-gen en_US.UTF-8
    dpkg-reconfigure locales
  2. Install PostgreSQL packages:
    • Red Hat
      $ sudo yum install postgresql-server
    • SLES
      $ sudo zypper install postgresql91-server
        Note: This command will install PostgreSQL 9.1. If you want to install a different version, you can use zypper search postgresql to search for available versions. You should install version 8.4 or higher.
    • Debian/Ubuntu
      $ sudo apt-get install postgresql

Configuring and Starting the PostgreSQL Server

By default, PostgreSQL only accepts connections on the loopback interface. You must reconfigure PostgreSQL to accept connections from the Fully Qualified Domain Name (FQDN) of the hosts hosting the management roles. If you do not make these changes, the management processes will not be able to connect to and use the database on which they depend.

  1. Initialize the external PostgreSQL database. For some versions of PostgreSQL, this is done automatically the first time that you start the PostgreSQL server. In this case, issue the command:
    $ sudo service postgresql start
    In other versions, you must explicitly initialize the database using:
    $ sudo service postgresql initdb
    See the PostgreSQL documentation for more details.
  2. Enable MD5 authentication. Edit pg_hba.conf, which is usually found in /var/lib/pgsql/data or /etc/postgresql/8.4/main. Add the following line:
    host all all md5
    If the default pg_hba.conf file contains the following line:
    host all all ident
    then the host line specifying md5 authentication shown above must be inserted before this ident line. Failure to do so may cause an authentication error when running the script. You can modify the contents of the md5 line shown above to support different configurations. For example, if you want to access PostgreSQL from a different host, replace with your IP address and update postgresql.conf, which is typically found in the same place as pg_hba.conf to include:
    listen_addresses = '*'
  3. Configure settings to ensure your system performs as expected. Update these settings in the /var/lib/pgsql/data/postgresql.conf or /var/lib/postgresql/data/postgresql.conf file. Settings vary based on cluster size and resources.
    • Small clusters - For small to mid-sized clusters, consider the following suggestions as a starting point for settings. If resources are especially limited, consider reducing the buffer sizes and checkpoint segments further. Ongoing tuning may be required based on each host's resource utilization. For example, if Cloudera Manager is running on the same host as other roles, the following values may be acceptable:
      • shared_buffers - 256MB
      • wal_buffers - 8MB
      • checkpoint_segments - 16
      • checkpoint_completion_target - 0.9
    • Large clusters - may contain up to 1000 hosts. For large clusters consider the following suggestions as a starting point for settings.
      • max_connection - For large clusters, each database is typically hosted on a different host. The general rule is to allow each database on a host 100 maximum connections and then add 50 extra connections. As a result, in the normal case for large clusters, configure each of the five hosts that hosts a single database for 150 connections. You may have to increase the system resources available to PostgreSQL, as described at Connection Settings.
      • shared_buffers - 1024MB. This requires that the operating system can allocate sufficient shared memory. See PostgreSQL information on Managing Kernel Resources for more information on setting kernel resources.
      • wal_buffers - 16MB. This value is derived from the shared_buffers value. Setting wal_buffers to be approximately 3% of shared_buffers up to a maximum of approximately 16MB works well in most case.
      • checkpoint_segments - 128. The PostgreSQL Tuning Guide recommends values between 32 and 256 for write-intensive systems, such as this one.
      • checkpoint_completion_target - 0.9. This setting is only available in PostgreSQL 8.3 and later. These versions are highly recommended.
  4. Configure the PostgreSQL server to start at boot.
    • Red Hat
      $ sudo /sbin/chkconfig postgresql on
      $ sudo /sbin/chkconfig --list postgresql
      postgresql          0:off   1:off   2:on    3:on    4:on    5:on    6:off
    • SLES
      $ sudo chkconfig --add postgresql
    • Debian/Ubuntu
      $ sudo chkconfig postgresql on
  5. Start or restart the PostgreSQL database:
    $ sudo service postgresql restart

Creating Databases for Activity Monitor, Reports Manager, Hive Metastore, Sentry Server, and Cloudera Navigator Audit Server

Create databases and user accounts for components that require databases:
  • If you are not using the Cloudera Manager installer, the Cloudera Manager Server.
  • Cloudera Management Service roles:
    • Activity Monitor (if using the MapReduce service)
    • Reports Manager
  • Each Hive Metastore
  • Sentry Server
  • Cloudera Navigator Audit Server

You can create these databases on the host where the Cloudera Manager Server will run, or on any other hosts in the cluster. For performance reasons, you should typically install each database on the host on which the service runs, as determined by the roles you will assign during installation or upgrade. In larger deployments or in cases where database administrators are managing the databases the services will use, databases may be separated from services, but do not undertake such an implementation lightly.

The database must be configured to support UTF-8 character set encoding.

Note the values you enter for database names, user names, and passwords. The Cloudera Manager installation wizard requires this information to correctly connect to these databases.

  1. Connect to PostgreSQL:
    $ sudo -u postgres psql
  2. If you are not using the Cloudera Manager installer, create a database for the Cloudera Manager Server. The database name, user name, and password can be anything you want. Be sure to note the names chosen, as you will need to supply them later when running the script.
    postgres=# CREATE ROLE scm LOGIN PASSWORD 'scm';
    postgres=# CREATE DATABASE scm OWNER scm ENCODING 'UTF8';
  3. Create databases for Activity Monitor, Reports Manager, Hive Metastore, Sentry Server, and Cloudera Navigator Audit Server:
    postgres=# CREATE ROLE user LOGIN PASSWORD 'password';
    postgres=# CREATE DATABASE databaseName OWNER user ENCODING 'UTF8';
    where user, password, and databaseName can be anything you want. The examples shown match the default names provided in the Cloudera Manager configuration settings:
    Role Database User Password
    Activity Monitor amon amon amon_password
    Reports Manager rman rman rman_password
    Hive Metastore Server metastore hive hive_password
    Sentry Server sentry sentry sentry_password
    Cloudera Navigator Audit Server nav nav nav_password
    For PostgreSQL 8.2.23 or later, also do:
    postgres=# ALTER DATABASE Metastore SET standard_conforming_strings = off;